Replica Props Sound Board
1M and 4M
(1m holds about 2min of audio, 4m holds about 6 min of audio)

Upload your own sounds or select from past projects listed below in the menu above or select upload for your own files to be programmed
This device allows you to add digital sound effects to any item. Simply select the sound effects you want and upload them. We will then program a tiny micro chip and ship it to you ready to install.

Important links

CLICK HERE FOR A SELECTION OF VIDEOS DEMONSTRATING STOCK OPTIONS	CLICK HERE FOR Wiring diagram,Assembly video, EXAMPLE PROJECTS and links to switches, amplifiers and breadboards
download helper for Firefox browser Lets you save any audio file you hear Like the starwars sounds here	www.goldwave.com For editing your sounds you can use the free Goldwave software.This software has a great noise filter button for cleaning up your sound files.

• Plays up to 10 sounds with their own switch. Up to 200 sounds can be played if you want the sounds to cycle through with a single button
• Assign features such as press and hold loop or single touch single play. Can be set to a constant loop with a latching switch.
  
• Add as many as 10 switches. Switches can be push button, tilt switch, shock sensor, or light activated.
• Runs off of 3 to 4.5 volts power depending on speaker size requirement.
  
• Total chip size is only 1.4" long x 0.75" wide x 0.30" thick (0.40" thick before solder stems are snipped)
• Sampling rate of up to 16KHz/12bit PWM out put. up to 0.5w 8ohm speaker power, Auto sleep mode to save power.
  

Includes pre-programmed micro chip and simple instructions. Only the sound module is supplied, you must supply your own switches, speaker, solderless bread board and battery holder. All are available at Radio Shack or Frys or at the link here

1. Select up to 10 sound files (more if you are doing a single button cycle) and place them in a zipped archive on your computer. You will need a program such as winzip or winrar to create a zip file. Some computers now come pre bundled.
   
2. Click on the upload button on the ordering page and navigate to your folder and then place your order.

By default your sounds will be programmed as indicated by you in a text file, or if no text file is included they will be programmed in random spots.
By default the play feature will be 'tap once to play.'
If you would like to assign your sounds with special features, include a .TXT file in your zip file with the following info:

• Sound order. Which sound you want on button 1-10
• Sound play special feature.
  

Example:
Sound number 1 play with push button loop. (This means if you push the button, the sound will loop repeatedly until you push the button again or another button is pressed. This is done on a latching switch such as a push on or push off. Will not work with momentary switches.) Uses for this might be for the hum of a motor or saber sound, or possibly a breathing sound or proton pack hum.
Sound number 2 play with press and hold loop. (This means the sound will loop as long as the button is held down. Works great with a momentary switch.) Uses for this might be for a laser beam or machine gun or proton thrower. Any repeating sound that you only want to play when a button is pressed.
Sound number 3 hold to play. (This means the sound will only play if the button is held down. So if you let go in the middle of the sound file the sound will instantly stop.) This is useful for a sound that does not need to play out its entire length but will play when activated; such as a saber clash or electrical discharge, or even the screech of tires.
Sound number 1 press to next. (This allows you to load up your 10 sounds but only have one button. Every time you press the switch, it moves to the next sound. This allows you to save room if you are limited on the amount of space in your project. Applications for this could be a free channel on your Radio Control droid or R/C car. Also a series of phrases for your Halloween costume. A great way to have realistic sounds in a plastic model with only one switch.

• Unused button assignment. If you have less than 10 sounds, we can assign the empty buttons other functions. If you only have 8 sounds, you can assign the remaining 2 buttons as volume controls up and down.

Your order will ship within 1 or 2 days and will include a simple to understand assembly instruction and your sound board. There is also a instructional video located in the links section above.

We suggest a 0.5w 8ohm speaker and a 4.5 volt power source such as 3 AAA batteries. Up to 5 volts can be used. Just make sure you don't over-power your speaker; doing so can cause static. We have tested a 65w speaker at 16ohms and it worked great. So larger applications are possible.

We will triple check your sound card prior to shipment to make sure it is as you requested.

Includes a 24" metal military style dog tag ball chain necklace.

Has a hole drilled just like the screen used prop.

We include a metal ball chain necklace, however some people have requested I locate the same black leather cord used on the show. I have found something very similar and you can purchase the cord here

Choose the 2mm, The hole for the necklace is not big enough for anything larger. The hole in the pendant is 3.16mm in diameter.

This is what the 2mm 20" cord looks like in a pendant

Revolution Fan? check out http://revolutiontvshow.net/

In this kit you will get the following items.

1. Key face with see through symbols

2. Key back, with pre- hollowed compartments that fit the electronics.

3. Magnets. (used to hold the key face to the key back

In order to complete this model, you will need the following items.

This item must be purchased from the below link

This prop is available in my shapeways shop. Please click on this link to place an order. You have the option of 3 materials. Sterling silver, translucent high resolution plastic or silver colored low resolution plastic. Click this link to go place an order

Please allow 2 weeks

This key is constructed from laser engraved acrylic and cast resin.

The key face connects to the main body with magnets for easy access to the electronics compartment. The battery flips out for quick changing. The switch is on the back of the key.

The yellow, blue and red led's glow brightly and illuminate through the engraved symbols on the face of the key.

This key is constructed from a special mirror coated acrylic that has been engraved to allow light to be transmitted through the symbols. The key consists of 2 1/8" thick sheets of acrylic which sandwich together the mirror material as well as the blue, red and yellow film to create the special effect of colored symbols. From the front you will only see the mirror coating with colored symbols. When a light is placed behind the key, the symbols will glow in color.